Basic Medical Dedicated Infant Phototherapy Incubator (ME3000AG)

Product Description:

How To Use The Infant Incubator ME3000AG:

First Point: Preparation
1. Do a good job of cleaning the whole machine and disinfection.
2. Lock the foot wheel of the whole machine to prevent the whole machine from moving.
3. The power cord -the end is inserted from the power supply input jack from the side of the chassis, and the other end is correctly inserted into the 220V/50Hz power socket, which is reliable.
4. Add an appropriate amount of distilled water to the water cup.

Second Point: Operation method
1. Turn on the power switch → the temperature controller enters the self -inspection status. Except for the ultra -temperature alarm indicator and the power -off alarm indicator, all indicators and digital tubes are on → All lights are destroyed → Display the temperature of the box and set the temperature value → If you do not press any keys, automatically enter the box temperature control status → The temperature value of the boot setting is to keep the setting value of the last shutdown.
2. Press the settings → Enter the box temperature setting status → set the temperature display window flickering. According to clinical needs, the temperature setting temperature is changed, push the add and subtract key to make the setting temperature display window consistent with the required value → Exit the setting state → enter the box temperature control state (if you do not press the box temperature key, wait for about 15 seconds to automatically enter the box temperature control status.

Third Point: Nursing method
When your baby cares, open the front panel lock, put down the front door panel, you can put in the baby, close the front door panel and lock the lock. When the baby needs to care, you can use the elbow to press the door lock and reach into the elliptical door for operation. In order to avoid the baby's cold, reduce the door opening time as much as possible. Hurry up and close the door after the completion.

The Precautions Of Medical Infant Incubator:
1. The cultivation box is not equipped with a purification device that improves air quality. In order to ensure the air quality in the infant incubator, the environmental temperature specified in the technical requirements of the infant incubator product must be used in the air environment with an environmental temperature of 20 ° C to 30 ° C and the relative humidity of 30%RH to 75%RH. The intensive care unit is used in similar ward.

2. In order to prevent harm to the patient, when the catheter, etc. are also connected to the patient or the crib is tilted and promoted, it is not allowed to open the baby cabin.

3. When the patient is still in the incubator, there is no need to open the infant incubator at any time. All contact with the patient can be performed by the front door baffle and operating window.

4. When the front and rear baffles are turned on, the temperature displayed by the box temperature may not be the actual temperature in the baby's cabin, so do not make the baffle open for a long time.

5. All baffle insertions should be inserted firmly to prevent accidental opening of the baffle.

6. When any abnormalities and faults occur in the equipment, stop using it immediately, turn off the power supply and transfer patients, and timely notify the company's after -sales service department or the maintenance provider authorized by the company. Do not repair and test by non -authorized personnel.

7. Direct sunlight or other radiant heat sources will increase the temperature of the infant incubator, but it will not start the ultra -temperature alarm function of the infant incubator. Therefore, the infant incubator cannot be placed in a place where the sunlight or other radiant thermal sources exist.

8. The infant incubator is a high -risk medical device that endangers the safety of human life. It can only be used in similar wards such as neonatal ward, pediatric ward, obstetric ward, and children's intensive care unit. The operator of the infant incubator must be trained and operates under the guidance of a practicing physician.

Product feature:
Air temp.and skin temp. servo-controlled by computer>37ºC temperature setting
Various self-check alarms
Free-step mattress tilting adjustment
Removable humidity reservoir , easy to clean
With the transfusion shelf and tray
Added with guardrail
RS-232 connectorPhototherapy(option)

FAQ:

If your company support OEM ?

Yes, we support OEM, You just sent me our your logo and requirement, we will print th logo in the products and nameplate.

What's our payment ways and methods?

Our payment ways is T/T: 30% before producing, and 70% before shipping the products.

L/C at sight and westunion.

Whats our delivery time for led light ?

For samll pc such as 1 pcs , the exact delivery time is about 5 days after get the payment.

For large pcs,such as 100 pcs, about one month after receive the advance payment.

What's your general shipping ways ?

Our general shipping ways is by sea, if customer is urgent also could arrange by air.